Equinox Systems GEMINI Manuel d'utilisateur Page 12
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Gemini Users Manual 7
Additionally, a second submenu item "Reset to Defaults" was introduced there to allow
you to reset only the Safety Limits to their default values (both east and west) without
having to reset all the other Setup values.
Another new submenu, “Set GoTo”, allows you to define a point past which Gemini will
always GoTo the object so that the telescope tube is on the east side of the mount.
Gemini will allow the mount to track past this point, but will not GoTo any object west of
this point without a meridian flip, if needed, to put the telescope tube on the east side of
the mount. The default value, displayed as 0 degrees, sets the GoTo limit to the western
safety limit minus 2.5 degrees, allowing for at least 10 minutes of tracking.
1.3.12 Selectable PC Synchronization Behavior
Gemini accepts two different kinds of Sync commands over the serial line. The LX200
protocol :CM# command shifts the internal coordinate system to reflect the latest position
correctly, "Synchronizing" it to an object. On the other hand, the additional ":Cm#
command uses the detected positional difference to enhance the internal pointing model.
The software running on a connected computer can choose between either.
Since there are still some software packages on the market not supporting the Additional
Align feature, Gemini's software now allows you to set the way :CM# and :Cm#
commands are interpreted. The Setup→Communication menu item now contains a "Sync
or Align" submenu. "Sync Only" selects Gemini's standard behavior as described above,
while "Sync→Add. Al." swaps the functionality of both commands, allowing
enhancement of the pointing model even with PC software not supporting this explicitly.
1.3.13 Precision Guiding Commands
The serial command protocol has been extended to allow precise movement commands to
be sent to Gemini. These commands include:
• Move at guide speed for a specific number of milliseconds
• Move at guide speed for a specific number of steps
• Move at guide speed for a specific number of arcseconds.
- Users Manual 1
- Table of Contents 2
- 1 Introduction 6
- 1.2 Features 7
- 1.3 What’s New in Level 4? 10
- 2 Getting Started 13
- 2.2 Installation 14
- 2.2.3 Encoders 15
- 2.2.4 Power Requirements 16
- 2.3.1 Controls 16
- 2.3.3 QuickMenu 18
- 2.4 Basics of Operation 19
- 2.4.1.2 Startup Position 20
- 2.4.2 Power On and Setup 20
- 2.4.2.2 Completing Startup 23
- 2.4.2.3 Preferences 23
- 2.4.4 Normal Operation 27
- 2.5 Next Steps 28
- 3.1.2 Precession 30
- 3.2 How the Sky Moves 31
- 3.3 Tracking 31
- 3.3.1.1 Predefined Rates 32
- Training Comet Tracking 35
- Timer Values 35
- PC Controlled Tracking 36
- 3.3.2 Meridian Flip 37
- 3.3.3 RA Safety Limits 37
- 3.4 Polar Alignment 39
- 3.4.3 Accuracy Required 41
- 3.5 Mount Modeling 42
- 3.5.3 Modeling Parameters 44
- 4.2 Guiding 45
- 4.2.2 Manual Guiding 46
- 4.2.5 Software Guiding 47
- 4.3.2 The PEC Submenu 49
- 4.3.2.1 Train PEC 49
- 4.3.2.2 Clear Data 50
- 4.3.2.3 Turn PEC On/Off 50
- 4.3.2.4 Delay Correction 50
- 4.3.2.5 Drift Correction 51
- 4.3.2.6 Smooth Data 52
- 4.3.2.7 Average Data 52
- 4.4 Other Functions 53
- 5.1 Startup Mode Menu 54
- 5.2 The Main Menu 55
- 5.3 Subordinate Menu System 56
- 5.3.1.2 {Reset Alignment} 57
- 5.3.1.3 {Additional Align} 57
- 5.3.1.4 Synchronize 58
- 5.3.1.5 {Polar Al. Assist} 58
- 5.3.1.6 {Polar Axis Corr.} 58
- 5.3.2 Object Database 59
- 5.3.2.1 Database Use 59
- 5.3.2.2 Accuracy and Epochs 60
- 5.3.2.3 Credits 60
- 5.3.2.6 IC (Index Catalog) 61
- 5.3.6.1 RA/DEC Display 64
- 5.3.6.2 Enter RA/DEC 64
- 5.3.6.3 Az/El Display 64
- 5.3.6.4 Enter Az/El 65
- 5.3.6.5 Set Bookmark 65
- 5.3.6.6 {GoTo Bookmark #n} 65
- 5.3.7 Identify 65
- 5.3.8 Object Search 66
- 5.3.8.2 Wobble Object 67
- 5.3.9 Show Date/Time 67
- 5.3.9.2 Julian Date 67
- 5.3.10 Setup 68
- 5.3.10.1 Hand Controller 69
- 5.3.10.2 Mount Parameters 69
- 5.3.10.2.1 Tracking Speed 70
- 5.3.10.2.2 Moving Speeds 71
- 5.3.10.2.5 Mount Type 72
- 5.3.10.2.8 {Pointing Model} 75
- 5.3.10.3 Encoder 76
- 5.3.10.4 Alarm/Buzzer 76
- 5.3.10.5 UTC Date/Time 77
- 5.3.10.6 Credit Info 77
- 5.3.10.7 Restore Defaults 78
- 5.3.10.8 Dim Display 78
- 5.3.10.9 Geogr. Location 78
- 5.3.10.9.5 Store Site 79
- 5.3.10.9.6 Load Site 79
- 5.3.10.10 Communication 80
- 5.3.10.10.2 Sync or Align 80
- 5.4 QuickMenu 81
- 5.4.1 Focusing 82
- 5.4.4 Centering 82
- 5.4.5 Park Mount! 83
- 5.4.6 Meridian Flip 83
- 5.4.7 Exit w/o Change 83
- 6 Serial Communication 85
- 6.2 Hand Controller port 87
- 6.3 Serial Command Sets 88
- 6.5.1 Telescope Driver 90
- 6.5.3 Coordinate Epoch 90
- 6.6 Using Control Programs 91
- 7 Troubleshooting 92
- 7.2 Debug Mode 96
- 8 Appendices 97
- QuickMenu 101
- Cold Start Setup Menu 101
- *Reduced Menu 101
- 8.2 Catalogs 102
- 8.3 Alignment Star List 103
- 8.4 Serial Line Protocol 105
- • Right Ascension 112
- • Declination {+ 112
- • the object name (up to 10 112
- Gemini Native Commands 116
- 8.5 Serial Communications 129
- 8.6 Autoguider Port 130
- 8.7 Encoder Port 132
- Connecting End Switches 133
- 8.8 Feature Port 134
- 8.9 Motor Connector Pinouts 135
- RJ-45 Connector 135
- DIN Connector 135
- 8.10 Power Connector Pinout 136
- Power Connector 136
- 8.11 Upgrading the EPROM 137
Produits connexes et manuels pour Lumières des projecteurs Equinox Systems GEMINI
(46 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.194 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels