Equinox Systems GEMINI Manuel d'utilisateur Page 28
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Gemini Users Manual 23
“Setup→Communication→Coordinate Epoch→Epoch J2000.0” menu item. You can
find more details on this in chapter 5.
Alternatively, you can enter coordinates of the azimuthal coordinate system using the
Coordinates->Enter Az/El submenu.
2.4.4.2 GoTo Operation
After an object has been selected (either from the internal catalogs or by entering its
coordinates) a new menu item appears: “GoTo <object>” (where <object> is the
currently selected object). Simply select this menu item to cause Gemini to slew to that
object. As the telescope approaches the object, it will ramp down from slew speed and
finish pointing at centering speed. When the GoTo is complete, the display will show
“FINISHED.” If you have correctly built a good pointing model, the object should be
within a few arc minutes of the center of the field of view. You can then center it using
the Hand Controller, and either Synchronize, or perform an Additional Align if you want
to continue to refine the pointing model.
2.4.4.3 Tracking
By default, Gemini will track at the sidereal rate. This should be sufficient for visually
observing nearly any object if you are roughly polar aligned, but the tracking can be
changed to other rates if desired. It is important to note that continuous tracking will
occur while in either the Menu Mode or the Telescope Control Mode.
2.5 Next Steps
The steps outlined above are sufficient to get you started and provide you with many
hours of observing pleasure. However, we have only scratched the surface of the
Gemini’s many capabilities. Please take some time to read through the rest of the manual
for information regarding such topics as:
• Using Gemini to achieve better polar alignment
• Imaging (tracking rates, Periodic Error Control, using an autoguider, etc.)
• Startup modes
• Mount modeling
2.5.1 Gemini Users’ Group
You can exchange information and ideas with other Gemini users on the Gemini Users’
Group forum on Yahoo. You can get more information or join the group at
http://groups.yahoo.com/group/Gemini_Users.
- Users Manual 1
- Table of Contents 2
- 1 Introduction 6
- 1.2 Features 7
- 1.3 What’s New in Level 4? 10
- 2 Getting Started 13
- 2.2 Installation 14
- 2.2.3 Encoders 15
- 2.2.4 Power Requirements 16
- 2.3.1 Controls 16
- 2.3.3 QuickMenu 18
- 2.4 Basics of Operation 19
- 2.4.1.2 Startup Position 20
- 2.4.2 Power On and Setup 20
- 2.4.2.2 Completing Startup 23
- 2.4.2.3 Preferences 23
- 2.4.4 Normal Operation 27
- 2.5 Next Steps 28
- 3.1.2 Precession 30
- 3.2 How the Sky Moves 31
- 3.3 Tracking 31
- 3.3.1.1 Predefined Rates 32
- Training Comet Tracking 35
- Timer Values 35
- PC Controlled Tracking 36
- 3.3.2 Meridian Flip 37
- 3.3.3 RA Safety Limits 37
- 3.4 Polar Alignment 39
- 3.4.3 Accuracy Required 41
- 3.5 Mount Modeling 42
- 3.5.3 Modeling Parameters 44
- 4.2 Guiding 45
- 4.2.2 Manual Guiding 46
- 4.2.5 Software Guiding 47
- 4.3.2 The PEC Submenu 49
- 4.3.2.1 Train PEC 49
- 4.3.2.2 Clear Data 50
- 4.3.2.3 Turn PEC On/Off 50
- 4.3.2.4 Delay Correction 50
- 4.3.2.5 Drift Correction 51
- 4.3.2.6 Smooth Data 52
- 4.3.2.7 Average Data 52
- 4.4 Other Functions 53
- 5.1 Startup Mode Menu 54
- 5.2 The Main Menu 55
- 5.3 Subordinate Menu System 56
- 5.3.1.2 {Reset Alignment} 57
- 5.3.1.3 {Additional Align} 57
- 5.3.1.4 Synchronize 58
- 5.3.1.5 {Polar Al. Assist} 58
- 5.3.1.6 {Polar Axis Corr.} 58
- 5.3.2 Object Database 59
- 5.3.2.1 Database Use 59
- 5.3.2.2 Accuracy and Epochs 60
- 5.3.2.3 Credits 60
- 5.3.2.6 IC (Index Catalog) 61
- 5.3.6.1 RA/DEC Display 64
- 5.3.6.2 Enter RA/DEC 64
- 5.3.6.3 Az/El Display 64
- 5.3.6.4 Enter Az/El 65
- 5.3.6.5 Set Bookmark 65
- 5.3.6.6 {GoTo Bookmark #n} 65
- 5.3.7 Identify 65
- 5.3.8 Object Search 66
- 5.3.8.2 Wobble Object 67
- 5.3.9 Show Date/Time 67
- 5.3.9.2 Julian Date 67
- 5.3.10 Setup 68
- 5.3.10.1 Hand Controller 69
- 5.3.10.2 Mount Parameters 69
- 5.3.10.2.1 Tracking Speed 70
- 5.3.10.2.2 Moving Speeds 71
- 5.3.10.2.5 Mount Type 72
- 5.3.10.2.8 {Pointing Model} 75
- 5.3.10.3 Encoder 76
- 5.3.10.4 Alarm/Buzzer 76
- 5.3.10.5 UTC Date/Time 77
- 5.3.10.6 Credit Info 77
- 5.3.10.7 Restore Defaults 78
- 5.3.10.8 Dim Display 78
- 5.3.10.9 Geogr. Location 78
- 5.3.10.9.5 Store Site 79
- 5.3.10.9.6 Load Site 79
- 5.3.10.10 Communication 80
- 5.3.10.10.2 Sync or Align 80
- 5.4 QuickMenu 81
- 5.4.1 Focusing 82
- 5.4.4 Centering 82
- 5.4.5 Park Mount! 83
- 5.4.6 Meridian Flip 83
- 5.4.7 Exit w/o Change 83
- 6 Serial Communication 85
- 6.2 Hand Controller port 87
- 6.3 Serial Command Sets 88
- 6.5.1 Telescope Driver 90
- 6.5.3 Coordinate Epoch 90
- 6.6 Using Control Programs 91
- 7 Troubleshooting 92
- 7.2 Debug Mode 96
- 8 Appendices 97
- QuickMenu 101
- Cold Start Setup Menu 101
- *Reduced Menu 101
- 8.2 Catalogs 102
- 8.3 Alignment Star List 103
- 8.4 Serial Line Protocol 105
- • Right Ascension 112
- • Declination {+ 112
- • the object name (up to 10 112
- Gemini Native Commands 116
- 8.5 Serial Communications 129
- 8.6 Autoguider Port 130
- 8.7 Encoder Port 132
- Connecting End Switches 133
- 8.8 Feature Port 134
- 8.9 Motor Connector Pinouts 135
- RJ-45 Connector 135
- DIN Connector 135
- 8.10 Power Connector Pinout 136
- Power Connector 136
- 8.11 Upgrading the EPROM 137
Produits connexes et manuels pour Lumières des projecteurs Equinox Systems GEMINI
(46 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels