Equinox Systems GEMINI Manuel d'utilisateur Page 96
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Gemini Users Manual 91
the “Setup” menu to set all of the appropriate settings for your mount (see chapter
2). If the problem persists, contact your dealer.
Note: Mountain Instruments and some Losmandy dealers set some mount
parameters such as latitude and longitude to the correct value for individual
customers before shipping the mounts. Replacing the battery resets all values,
including mount type, latitude and longitude to their default values, requiring the
user to enter the correct values for their location.
7.1.16 Gemini Displays “DEC/RA motor lags”
• This message indicates that one of the servo motors (either RA or Dec. depending
on the exact message) is not moving as smoothly as it should, typically at slow
speeds (guiding and/or tracking). It is detected when the motor is some number
of steps away from the expected position, and Gemini increases the amount of
current to the motor in order to get it to move. This may be caused by a tight spot
in the gear mesh or by a balance problem. If higher current continues to flow in
order to overcome whatever problem exists, the motor will heat up and may
eventually burn out. This message is an early warning that you should check the
motor temperature, and possibly adjust your worm mesh or the mount balance.
7.2 Debug Mode
If you have problems with the serial link to your computer or your planetarium software,
you can press one of the Hand Controller keys while powering up. Doing this will put
Gemini into "Debug Mode" and show all commands that are received from the PC in the
Information Buffer. You can scroll through this buffer with the "Show Information"
menu item. You should see the commands sent by the software (omitting numerical
values), that are ASCII characters (e.g. ":GR#:GD#"). If not, the serial link is not
operational.
The phrase "Debug Mode” is appended to the welcome message when Gemini is started
up in Debug Mode.
- Users Manual 1
- Table of Contents 2
- 1 Introduction 6
- 1.2 Features 7
- 1.3 What’s New in Level 4? 10
- 2 Getting Started 13
- 2.2 Installation 14
- 2.2.3 Encoders 15
- 2.2.4 Power Requirements 16
- 2.3.1 Controls 16
- 2.3.3 QuickMenu 18
- 2.4 Basics of Operation 19
- 2.4.1.2 Startup Position 20
- 2.4.2 Power On and Setup 20
- 2.4.2.2 Completing Startup 23
- 2.4.2.3 Preferences 23
- 2.4.4 Normal Operation 27
- 2.5 Next Steps 28
- 3.1.2 Precession 30
- 3.2 How the Sky Moves 31
- 3.3 Tracking 31
- 3.3.1.1 Predefined Rates 32
- Training Comet Tracking 35
- Timer Values 35
- PC Controlled Tracking 36
- 3.3.2 Meridian Flip 37
- 3.3.3 RA Safety Limits 37
- 3.4 Polar Alignment 39
- 3.4.3 Accuracy Required 41
- 3.5 Mount Modeling 42
- 3.5.3 Modeling Parameters 44
- 4.2 Guiding 45
- 4.2.2 Manual Guiding 46
- 4.2.5 Software Guiding 47
- 4.3.2 The PEC Submenu 49
- 4.3.2.1 Train PEC 49
- 4.3.2.2 Clear Data 50
- 4.3.2.3 Turn PEC On/Off 50
- 4.3.2.4 Delay Correction 50
- 4.3.2.5 Drift Correction 51
- 4.3.2.6 Smooth Data 52
- 4.3.2.7 Average Data 52
- 4.4 Other Functions 53
- 5.1 Startup Mode Menu 54
- 5.2 The Main Menu 55
- 5.3 Subordinate Menu System 56
- 5.3.1.2 {Reset Alignment} 57
- 5.3.1.3 {Additional Align} 57
- 5.3.1.4 Synchronize 58
- 5.3.1.5 {Polar Al. Assist} 58
- 5.3.1.6 {Polar Axis Corr.} 58
- 5.3.2 Object Database 59
- 5.3.2.1 Database Use 59
- 5.3.2.2 Accuracy and Epochs 60
- 5.3.2.3 Credits 60
- 5.3.2.6 IC (Index Catalog) 61
- 5.3.6.1 RA/DEC Display 64
- 5.3.6.2 Enter RA/DEC 64
- 5.3.6.3 Az/El Display 64
- 5.3.6.4 Enter Az/El 65
- 5.3.6.5 Set Bookmark 65
- 5.3.6.6 {GoTo Bookmark #n} 65
- 5.3.7 Identify 65
- 5.3.8 Object Search 66
- 5.3.8.2 Wobble Object 67
- 5.3.9 Show Date/Time 67
- 5.3.9.2 Julian Date 67
- 5.3.10 Setup 68
- 5.3.10.1 Hand Controller 69
- 5.3.10.2 Mount Parameters 69
- 5.3.10.2.1 Tracking Speed 70
- 5.3.10.2.2 Moving Speeds 71
- 5.3.10.2.5 Mount Type 72
- 5.3.10.2.8 {Pointing Model} 75
- 5.3.10.3 Encoder 76
- 5.3.10.4 Alarm/Buzzer 76
- 5.3.10.5 UTC Date/Time 77
- 5.3.10.6 Credit Info 77
- 5.3.10.7 Restore Defaults 78
- 5.3.10.8 Dim Display 78
- 5.3.10.9 Geogr. Location 78
- 5.3.10.9.5 Store Site 79
- 5.3.10.9.6 Load Site 79
- 5.3.10.10 Communication 80
- 5.3.10.10.2 Sync or Align 80
- 5.4 QuickMenu 81
- 5.4.1 Focusing 82
- 5.4.4 Centering 82
- 5.4.5 Park Mount! 83
- 5.4.6 Meridian Flip 83
- 5.4.7 Exit w/o Change 83
- 6 Serial Communication 85
- 6.2 Hand Controller port 87
- 6.3 Serial Command Sets 88
- 6.5.1 Telescope Driver 90
- 6.5.3 Coordinate Epoch 90
- 6.6 Using Control Programs 91
- 7 Troubleshooting 92
- 7.2 Debug Mode 96
- 8 Appendices 97
- QuickMenu 101
- Cold Start Setup Menu 101
- *Reduced Menu 101
- 8.2 Catalogs 102
- 8.3 Alignment Star List 103
- 8.4 Serial Line Protocol 105
- • Right Ascension 112
- • Declination {+ 112
- • the object name (up to 10 112
- Gemini Native Commands 116
- 8.5 Serial Communications 129
- 8.6 Autoguider Port 130
- 8.7 Encoder Port 132
- Connecting End Switches 133
- 8.8 Feature Port 134
- 8.9 Motor Connector Pinouts 135
- RJ-45 Connector 135
- DIN Connector 135
- 8.10 Power Connector Pinout 136
- Power Connector 136
- 8.11 Upgrading the EPROM 137
Produits connexes et manuels pour Lumières des projecteurs Equinox Systems GEMINI
(46 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels