Equinox Systems GEMINI Manuel d'utilisateur Page 88
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Gemini Users Manual 83
internal micro controller with 5V TTL signals, an adapter is necessary to use it to
communicate with RS232 ports. Adapters for Bluetooth or USB can be designed.
Several adapters are available from third party sources.
If an adapter is connected to make use of the second serial port, the Deluxe Hand
Controller cannot be connected. However, the classic hand controller can still be used to
slew the telescope. The onboard display of the first generation Gemini units will be
disabled by the adapter. All hand controller functions are also available using the Gemini
Control Center software Hand Controller Emulation mode (see section 6.6.1 below).
The table below gives the pinouts of the DB15 hand controller port:
Gemini DB15 socket Function
Pin 1 +5V
Pin 2 +5.4V
Pin 4 Menu button (active Low)
Pin 5 GND Signal Ground
Pin 6 LED (minus, with resistor, LED+ at +5V
or 5.4V)
Pin 7 RA- (left button, all buttons active High,
3.3k load)
Pin 8 DEC- (down)
Pin 9 DEC+ (up)
Pin 10 RA+ (right)
Pin 11 RxD Received Data (5V TTL, serial input
to Gemini)
Pin 14 Connect to GND to enable the use of pins
11 and 14 as serial channels and disable
onboard LED displays.
Pin 15 TxD Transmitted Data (5V TTL, serial
output from Gemini)
6.3 Serial Command Sets
6.3.1 Meade
LX200 Commands
Gemini supports a subset of the LX200 command set that is necessary for the control of
German Equatorial Mounts. The majority of these commands start with a colon “:” and
end with a hash mark“#”. Each character received is stored into a buffer. After the hash
(or an ACK character) is received, Gemini interprets and executes the command(s).
In addition to the commands defined by Meade Corporation, Gemini supports additional,
LX200-like commands following the syntactic rules described above. Both are described
in Appendix 8.4, Serial Line Protocol.
- Users Manual 1
- Table of Contents 2
- 1 Introduction 6
- 1.2 Features 7
- 1.3 What’s New in Level 4? 10
- 2 Getting Started 13
- 2.2 Installation 14
- 2.2.3 Encoders 15
- 2.2.4 Power Requirements 16
- 2.3.1 Controls 16
- 2.3.3 QuickMenu 18
- 2.4 Basics of Operation 19
- 2.4.1.2 Startup Position 20
- 2.4.2 Power On and Setup 20
- 2.4.2.2 Completing Startup 23
- 2.4.2.3 Preferences 23
- 2.4.4 Normal Operation 27
- 2.5 Next Steps 28
- 3.1.2 Precession 30
- 3.2 How the Sky Moves 31
- 3.3 Tracking 31
- 3.3.1.1 Predefined Rates 32
- Training Comet Tracking 35
- Timer Values 35
- PC Controlled Tracking 36
- 3.3.2 Meridian Flip 37
- 3.3.3 RA Safety Limits 37
- 3.4 Polar Alignment 39
- 3.4.3 Accuracy Required 41
- 3.5 Mount Modeling 42
- 3.5.3 Modeling Parameters 44
- 4.2 Guiding 45
- 4.2.2 Manual Guiding 46
- 4.2.5 Software Guiding 47
- 4.3.2 The PEC Submenu 49
- 4.3.2.1 Train PEC 49
- 4.3.2.2 Clear Data 50
- 4.3.2.3 Turn PEC On/Off 50
- 4.3.2.4 Delay Correction 50
- 4.3.2.5 Drift Correction 51
- 4.3.2.6 Smooth Data 52
- 4.3.2.7 Average Data 52
- 4.4 Other Functions 53
- 5.1 Startup Mode Menu 54
- 5.2 The Main Menu 55
- 5.3 Subordinate Menu System 56
- 5.3.1.2 {Reset Alignment} 57
- 5.3.1.3 {Additional Align} 57
- 5.3.1.4 Synchronize 58
- 5.3.1.5 {Polar Al. Assist} 58
- 5.3.1.6 {Polar Axis Corr.} 58
- 5.3.2 Object Database 59
- 5.3.2.1 Database Use 59
- 5.3.2.2 Accuracy and Epochs 60
- 5.3.2.3 Credits 60
- 5.3.2.6 IC (Index Catalog) 61
- 5.3.6.1 RA/DEC Display 64
- 5.3.6.2 Enter RA/DEC 64
- 5.3.6.3 Az/El Display 64
- 5.3.6.4 Enter Az/El 65
- 5.3.6.5 Set Bookmark 65
- 5.3.6.6 {GoTo Bookmark #n} 65
- 5.3.7 Identify 65
- 5.3.8 Object Search 66
- 5.3.8.2 Wobble Object 67
- 5.3.9 Show Date/Time 67
- 5.3.9.2 Julian Date 67
- 5.3.10 Setup 68
- 5.3.10.1 Hand Controller 69
- 5.3.10.2 Mount Parameters 69
- 5.3.10.2.1 Tracking Speed 70
- 5.3.10.2.2 Moving Speeds 71
- 5.3.10.2.5 Mount Type 72
- 5.3.10.2.8 {Pointing Model} 75
- 5.3.10.3 Encoder 76
- 5.3.10.4 Alarm/Buzzer 76
- 5.3.10.5 UTC Date/Time 77
- 5.3.10.6 Credit Info 77
- 5.3.10.7 Restore Defaults 78
- 5.3.10.8 Dim Display 78
- 5.3.10.9 Geogr. Location 78
- 5.3.10.9.5 Store Site 79
- 5.3.10.9.6 Load Site 79
- 5.3.10.10 Communication 80
- 5.3.10.10.2 Sync or Align 80
- 5.4 QuickMenu 81
- 5.4.1 Focusing 82
- 5.4.4 Centering 82
- 5.4.5 Park Mount! 83
- 5.4.6 Meridian Flip 83
- 5.4.7 Exit w/o Change 83
- 6 Serial Communication 85
- 6.2 Hand Controller port 87
- 6.3 Serial Command Sets 88
- 6.5.1 Telescope Driver 90
- 6.5.3 Coordinate Epoch 90
- 6.6 Using Control Programs 91
- 7 Troubleshooting 92
- 7.2 Debug Mode 96
- 8 Appendices 97
- QuickMenu 101
- Cold Start Setup Menu 101
- *Reduced Menu 101
- 8.2 Catalogs 102
- 8.3 Alignment Star List 103
- 8.4 Serial Line Protocol 105
- • Right Ascension 112
- • Declination {+ 112
- • the object name (up to 10 112
- Gemini Native Commands 116
- 8.5 Serial Communications 129
- 8.6 Autoguider Port 130
- 8.7 Encoder Port 132
- Connecting End Switches 133
- 8.8 Feature Port 134
- 8.9 Motor Connector Pinouts 135
- RJ-45 Connector 135
- DIN Connector 135
- 8.10 Power Connector Pinout 136
- Power Connector 136
- 8.11 Upgrading the EPROM 137
Produits connexes et manuels pour Lumières des projecteurs Equinox Systems GEMINI
(46 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels